Analysis and optimization of current collecting systems in PEM fuel cells

Persistent Link:
http://hdl.handle.net/10150/610164
Title:
Analysis and optimization of current collecting systems in PEM fuel cells
Author:
Li, Peiwen; Ki, Jeong-Pill; Liu, Hong
Affiliation:
Department of Aerospace and Mechanical Engineering, University of Arizona, Tucson, AZ, 85721, USA; Current address: Department of Mechanical and Aerospace Engineering, University of Texas at Arlington, Arlington, TX, 76019, USA
Issue Date:
2012
Publisher:
SpringerOpen
Citation:
Li et al. International Journal of Energy and Environmental Engineering 2012, 3:2 http://www.journal-ijeee.com/content/3/1/2
Journal:
International Journal of Energy and Environmental Engineering
Rights:
© 2012 Li et al; licensee Springer. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0)
Collection Information:
This item is part of the UA Faculty Publications collection. For more information this item or other items in the UA Campus Repository, contact the University of Arizona Libraries at repository@u.library.arizona.edu.
Abstract:
This paper presents analytical and experimental studies on optimization of the gas delivery and current collection system in a proton exchange membrane (PEM) fuel cell for the objective of reducing ohmic loss, thereby achieving higher power density. Specifically, the dimensions of current collection ribs as well as the rib distribution were optimized to get a maximized power density in a fuel cell. In the modeling process, the power output from a fixed area of membrane is calculated through analysis of an electrical circuit simulating the current from electrochemical reaction flowing to the current collectors. Current collectors of two-dimensional ribs and three-dimensional pillars were considered. Analyses found that three-dimensional pillars allow higher power density in a PEM fuel cell. Considering the mass transfer enhancement effect, three-dimensional pillars as current collectors in gas flow field may be a good choice if the fuel cell operates at low current density and there is no liquid water blocking the flow channels. The analyses did not consider the existence of liquid water, meaning the current density is not very high. The study concluded that decreasing the size of both the current collector and its control area yields a significant benefit to a higher power density. A preliminary experimental test in a PEM fuel cell has verified the conclusion of the analytical work.
EISSN:
2008-9163
DOI:
10.1186/2251-6832-3-2
Keywords:
Proton-exchange-membrane fuel cell; Optimization; Current collectors; Analysis
Version:
Final published version
Additional Links:
http://link.springer.com/article/10.1186/2251-6832-3-2

Full metadata record

DC FieldValue Language
dc.contributor.authorLi, Peiwenen
dc.contributor.authorKi, Jeong-Pillen
dc.contributor.authorLiu, Hongen
dc.date.accessioned2016-05-20T09:00:05Z-
dc.date.available2016-05-20T09:00:05Z-
dc.date.issued2012en
dc.identifier.citationLi et al. International Journal of Energy and Environmental Engineering 2012, 3:2 http://www.journal-ijeee.com/content/3/1/2en
dc.identifier.doi10.1186/2251-6832-3-2en
dc.identifier.urihttp://hdl.handle.net/10150/610164-
dc.description.abstractThis paper presents analytical and experimental studies on optimization of the gas delivery and current collection system in a proton exchange membrane (PEM) fuel cell for the objective of reducing ohmic loss, thereby achieving higher power density. Specifically, the dimensions of current collection ribs as well as the rib distribution were optimized to get a maximized power density in a fuel cell. In the modeling process, the power output from a fixed area of membrane is calculated through analysis of an electrical circuit simulating the current from electrochemical reaction flowing to the current collectors. Current collectors of two-dimensional ribs and three-dimensional pillars were considered. Analyses found that three-dimensional pillars allow higher power density in a PEM fuel cell. Considering the mass transfer enhancement effect, three-dimensional pillars as current collectors in gas flow field may be a good choice if the fuel cell operates at low current density and there is no liquid water blocking the flow channels. The analyses did not consider the existence of liquid water, meaning the current density is not very high. The study concluded that decreasing the size of both the current collector and its control area yields a significant benefit to a higher power density. A preliminary experimental test in a PEM fuel cell has verified the conclusion of the analytical work.en
dc.language.isoenen
dc.publisherSpringerOpenen
dc.relation.urlhttp://link.springer.com/article/10.1186/2251-6832-3-2en
dc.rights© 2012 Li et al; licensee Springer. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0)en
dc.subjectProton-exchange-membrane fuel cellen
dc.subjectOptimizationen
dc.subjectCurrent collectorsen
dc.subjectAnalysisen
dc.titleAnalysis and optimization of current collecting systems in PEM fuel cellsen
dc.typeArticleen
dc.identifier.eissn2008-9163en
dc.contributor.departmentDepartment of Aerospace and Mechanical Engineering, University of Arizona, Tucson, AZ, 85721, USAen
dc.contributor.departmentCurrent address: Department of Mechanical and Aerospace Engineering, University of Texas at Arlington, Arlington, TX, 76019, USAen
dc.identifier.journalInternational Journal of Energy and Environmental Engineeringen
dc.description.collectioninformationThis item is part of the UA Faculty Publications collection. For more information this item or other items in the UA Campus Repository, contact the University of Arizona Libraries at repository@u.library.arizona.edu.en
dc.eprint.versionFinal published versionen
All Items in UA Campus Repository are protected by copyright, with all rights reserved, unless otherwise indicated.